✎ DMX RGB Decoder 3 channel control DC12V/24V 3A/CH [DMX512.RU Управление светом]

Отредактируйте страницу и нажмите «Сохранить». Прочтите справочную страницу для ознакомления с синтаксисом вики. Пожалуйста, редактируйте только в том случае, если планируете улучшить содержимое. Если вы просто хотите потестировать что-либо, воспользуйтесь специальной страницей: PlayGround.

====== DMX RGB Decoder 3 channel control DC12V/24V 3A/CH ======
The 3-channel DMX controller controls __3 DMX channels__. It is actually a real dimmer block for rgb tapes. It is one of the cheapest decoders on the market. Production China.

{{:manual:dmxrgbdecoder:dc12-24v-px24606-dmx-constant-voltage-decoder-dmx-512-led-controler-6a-1-channel-output.jpg?nolink|DMX 512 Decoder}}
===== Description =====
The **DMX24506** uses a modern microcomputer
Control technology and converts the widely used
__Digital signal DMX24506 in the analog__. As options, you can
But use from 1 to 3 channels with 256 shades of gray. Also
The device can be used as a PC connector
Controlled digital lighting controller and analog
Modulator of illumination. As a rule, the decoder is used for
LED building lighting control.
===== Functions =====
  * Compliance with DMX512.
  * 256 levels of brightness, full color control.
  * 3 channels with a current load of up to **3A on each channel**.
  * Excellent effects thanks to the control system.
  * Thanks to the mechanism for selecting colors, you can control from 1 to 3 colors.
  * Independent DMX address setting.
  * Ability to specify the requirements of the customer.
{{:manual:dmxrgbdecoder:t2ec16n_zue9s389y-ybr_6rdrp_g_60_35.jpg?nolink&350 |DMX RGB DECODER FRONT}} 
|     ** Specifications ** ^
^ Control Channels | 3 channels ((Each channel is controlled separately)) |
^ Values | 256 channel values |
^ Output power | 3 Amperes per channel ((Each channel gives out 3 amps)) |
^ Effects | Inclusion, intensity, mixing |
^ DMX | Set the address of the DIP switches. | | |
^ Working voltage | 12-24V |
^ Operating temperature range: | 0 ~ 50 ° C. | | |
^ Overall dimensions: | 86 (mm) * 51 (mm) * 17.8 (mm). | | |
^ Power consumption in standby mode: | <1W. | | |
^ Weight: | 110g. | | |
^ Optional | Power can be increased by amplifiers |

===== Interface Description =====
Input DMX IN and output DMX OUT interfaces can be interchangeable.
Address setting interface
For usage procedures, refer to the "//**DMX address code table**//".
The table of addresses of codes of series **DMX**.
**12-24VDC** input, power supply for decoder and lamps.
==== Driver Output Interface ====
The common anode, V + and R, G, B interface can control the RGB module or single-color module. WHO-
The ability to control the output current in relation to the actual load.
Notes: Connect the positive lead and RGB wire of the common anode of the RGB module.
To the output interface of the decoder.
Connect the positive terminal of the monochrome module to the V+ on the decoder, and the negative output to the
One of the RGB module outputs according to the color of the LED.
Connect several single-color models to one decoder, with their positive output
Connect to the V+ terminal on the decoder.
===== Connecting the DMX-512 signal =====
The DMX512 signal uses a **CAT-5 cable** or a three-wire braided cable, while the DMX-
The signal has a positive (+) and negative (-) poles. When soldering the DMX-
Should be observed so that there is no short circuit between the positive
(+) And negative (-) poles, and then connect the cable
Corresponding to the input interface of the DMX24506.
<note important>Connect the signal output to the end of the entire connection (you need to install DIP-Switches DMX24506 to the off state).</note>
===== Where to buy =====
[[http://ali.pub/42pwn|Buy on Аliexpress - ~15$ - 25$.
]]

Пожалуйста, введите код подтверждения, чтобы доказать, что вы человек: Z W H F P Пожалуйста, оставьте это поле пустым:

Сводка изменений